VENTSURE® 4-FOOT STRIP HEAT & MOISTURE RIDGE VENTS with Weather PROtector® Moisture Barrier INSTALLATION INSTRUCTIONS Instrucciones para la instalación ^ ----- page break ----- Owens Corning® VentSure® 4-Foot Fig. 1 Instrucciones de instalación para Strip Heat & Moisture Ridge Vent la ventilación de cumbrera para la Installation Instructions eliminación de calor y humedad en tiras de 4 pies de Owens Corning® VentSure® 4-Foot Strip Ridge Vents are VentSure® designed for roofs with slopes of 3/12 to 16/12. Las ventilaciones de cumbrera VentSure® de 4 pies están diseñadas para pendientes con Intake at the eave vents should be equal or inclinaciones de 3/12 a 16/12. exceed that of the ridge vent being installed. La entrada de aire de las ventilaciones de IMPORTANT NOTES los aleros debería ser igual o mayor a la de las ventilaciones de cumbrera que se están 1. Before applying vent to architectural instalando. Las ventilaciones de cumbrera shingles, leave underlayment long at ridge VentSure® se han diseñado para aplicaciones and fold back under vent or caulk between residenciales. low areas of shingle and flange of vent, making sure you don't plug drain holes. This Fig. 2 NOTAS IMPORTANTES will help prevent wind driven rain and snow Fig. 3 from entering the attic. 1. Antes de colocar la ventilación sobre tejas arquitectónicas, deje un excedente de fieltro 2. See instructions for cutting slot. sobre la cumbrera y dóblelo introduciéndolo debajo de la ventilación, o selle los espacios 3. For structures with different ridge heights, entre las áreas bajas de la teja y el ala de be sure to vent the higher ridge provided la ventilación asegurándose de no obstruir there is an opening that connects the two orificios de drenaje. Esto ayudará a impedir attic spaces. que la lluvia y la nieve se filtren al ático por la acción del viento. It is also acceptable to vent lower ridges with dormers. 2. Consulte las instrucciones para saber cómo realizar el corte de la ranura. 4. For truss roof framing, cut a 1 inch slot on each side of the ridge starting a minimum of 3. Para estructuras con cumbreras de 6 inches from the rake edge of the roof. diferentes alturas, asegúrese de ventilar la cumbrera más alta; también es aceptable For conventionally framed roofs with a ventilar las cumbreras inferiores con center ridge board, cut a 1 inch wide slot buhardillas. beyond the ridge board starting a minimum of 6 inches from the rake edge of the roof. 4. En el caso de los cabrios del armazón, Combined width of slots and ridge board corte una ranura de 1 pulgadas a cada lado should not exceed 3½ inches. de la cumbrera a partir de 6 pulgadas, como mínimo, de la cornisa del tímpano del techo. 5. For best appearance, run VentSure® Ridge En el caso de techos con un poste central, Vent from end to end to give the roof a more corte una ranura de 1 pulgadas a cada lado attractive appearance. de la cumbrera a partir de 6 pulgadas, como mínimo, de la cornisa del tímpano del techo. Installation Instructions 5. Para una mayor estética, coloque la 1. Using a chalk line, mark out 1 inch on both ventilación de cumbrera VentSure® de una sides of the ridge as a guide for cutting a slot punta a otra del techo para darle un aspecto in the top of the ridge. más atractivo. 2. Start and end 6 inches away from the rake Instrucciones de instalación edge of the roof, cut a slot using a circular saw with the blade set at a depth to cut 1. Trace una línea con tiza de modo de dejar through the wood sheathing only. Remove 1¼ pulgadas de cada lado de la cumbrera y the sheathing debris from slot. utilizarla como guía para cortar una ranura en la parte superior de la cumbrera. 3. Center the vent over the opening that has been cut in the ridge, ensuring the vent 2. A 6 pulgadas de la cornisa del tímpano sits flat on the roof. Also ensure that the del techo, corte una ranura usando una alignment tabs are facing the opposite sierra circular con la cuchilla ajustada a direction you will be installing the next piece una profundidad tal que el corte atraviese of ridge vent. For cold weather installation solamente el revestimiento de madera. leave a gap no bigger than inch to allow Limpie los vestigios del revestimiento de la for expansion. Gaps larger than inch could ranura. lead to rain and snow entering the attic. 3. Centre la ventilación sobre la abertura realizada en la cumbrera, asegurándose de que se apoye totalmente sobre el techo. También, asegúrese de que las lengüetas de alineación miren en dirección opuesta a la 2 Install Instructions | VentSure® 4-Foot Strip Heat & Moisture Ridge Vent with Weather PROtector® Moisture Barrier | April 2020 ----- page break ----- 4. As you install the vents ensure each vent Fig. 4 cual usted instale el siguiente segmento de is aligned, then nail in place using the nail Fig. 5 ventilación de cumbrera. Para instalaciones holes marked on each vent. en climas fríos, deje un espacio no mayor a pulgadas para dar lugar a la expansión. 5. Using a utility knife cut the final piece to a Si hubiera huecos mayores a pulgadas, length long enough so that it is flush with the podría haber filtraciones de lluvia y nieve en edge of the roof. Connect making sure that el ático. the built-in end caps are exposed and nail in place. 4. Al instalar las ventilaciones, asegúrese de que cada una esté alineada, luego clávela 6. Nail hip and ridge shingles over the utilizando los orificios para clavos que hay en vent using nails long enough to meet the cada una de ellas. penetration requirements of the local building code and shingle manufacturer or 5. Con un cúter, corte el tramo final a un use nails provided with the VentSure® ridge largo suficiente para que quede alineado vent. For a clean look, extend the hip and con el borde del techo. Asegúrese de que las ridge shingle to cover the alignment tabs or cofias integradas queden expuestas y fije con trim tabs off using a utility knife. clavos. INSTRUCTIONS FOR CUTTING SLOTS 6. Fije las tejas para limatesa y cumbrera sobre la ventilación con clavos con una Hip and Gable Roofs longitud que coincida con los requisitos de penetración del fabricante de las tejas o con Cut slot 1 inch on both sides of ridge to los clavos provistos junto con la ventilación within 6 inches of each end wall or hip de cumbrera VentSure®. Para una apariencia intersection. prolija, extienda la teja para limatesa y cumbrera de manera que cubra las lengüetas Chimneys de alineación o recorte las lengüetas con un cúter. Cut slots 12 inches from chimney. Run ridge vent from end of roof to butt against INSTRUCCIONES PARA EL CORTE DE chimney. RANURAS NOTE: Owens Corning's written warranty for Techos con hastiales y limatesas this product shall not apply in any instance in which the product was not installed in Corte ranuras de 1 pulgada a ambos lados de accordance with the instructions contained la cumbrera a una distancia de hasta 6 pulg. herein. See actual warranty for additional de la pared o intersección con la limatesa. warranty details. Fig. 6 Chimeneas Cortar las ranuras a 12 pulgadas de la chimenea. Coloque la ventilación de cumbrera desde el extremo del techo hasta tocar la chimenea. NOTA: La garantía escrita de Owens Corning para este producto no se aplicará en casos en que el producto no se haya instalado de acuerdo con las instrucciones aquí mencionadas. Install Instructions | VentSure® 4-Foot Strip Heat & Moisture Ridge Vent with Weather PROtector® Moisture Barrier | April 2020 3 ----- page break ----- "T" & "L" Roof Fig. 7 echo en "T" y en "L" Saw slots to within 12 inches of ridge 6 inches slot width Realice ranuras a 12 pulgadas de los puntos intersection points as shown. Install ridge 6 pulg. ancho de la ranura de intersección de la cumbrera como se vent completely across ridge on long side indica. Instale la ventilación a lo largo de and butt ridge vent on the short run against 6 inches from end wall to slot toda la cumbrera a cada lado de modo the side of the long run. 6 pulgadas de distancia antre que la ventilación de la cumbrera con el la pared y la ranura tramo corto toque contra el lado del tramo NOTE: To prevent leakage and preserve largo. Consulte la garantía para conocer los aesthetic roof line, always leave at least 6 End Wall detalles adicionales. inches between ridge slot and end of ridge. Pared NOTA: Para evitar goteras y conservar la NOTE: The net free area of soffit ventilation Fig. 8 línea estética del techo, siempre deje al should always be at least equal to or more menos 6 pulgadas entre la ranura de la than the net free area of the ridge ventilation. 12 inches 12 inches cumbrera y el borde de la cumbrera. 12 pulg. 12 pulg. LIMITED WARRANTY This product is NOTA: El área neta libre de la ventilación de covered by a Limited Warranty which is los sofitos siempre debe ser al menos igual available by calling 1-800-GET-PINK® o mayor al área libre neta de la ventilación de or visiting www.owenscorning.com. la cumbrera. THAT WARRANTY CONSTITUTES OUR GARANTÍA LIMITADA Este producto está EXCLUSIVE WARRANTY, AND WE HEREBY cubierto por una Garantía Limitada, la cual DISCLAIM ALL OTHER WARRANTIES, está disponible llamando al 1-800-GET- WHETHER EXPRESSED OR IMPLIED, PINK® o visitando nuestro sitio web en www. INCLUDING THE IMPLIED WARRANTIES owenscorning.com. OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT ESA GARANTÍA CONSTITUYE NUESTRA SHALL OWENS CORNING BE LIABLE TO GARANTÍA EXCLUSIVA, Y POR LA CUSTOMER FOR INCIDENTAL, INDIRECT OR PRESENTE SE RECHAZAN TODAS LAS CONSEQUENTIAL DAMAGES. DEMÁS GARANTÍAS, EXPRESAS O IMPLÍCITAS, INCLUYENDO LAS GARANTÍAS IMPLÍCITAS DE COMERCIABILIDAD E IDONEIDAD PARA UN PROPÓSITO PARTICULAR. EN NINGÚN CASO OWENS CORNING SERÁ RESPONSABLE ANTE EL CLIENTE POR DAÑOS INCIDENTALES, INDIRECTOS O CONSECUENTES. 6 inches 12 inches Fig. 9 6 pulg. 12 pulg. 6 inches 12 inches 6 pulg. 12 inches 12 pulg. 12 pulg. OWENS CORNING ROOFING AND ASPHALT, LLC ONE OWENS CORNING PARKWAY TOLEDO, OHIO 43659 1-800 - G E T- P I N K® www.owenscorning.com Pub. No.10011388-C. THE PINK PANTHERTM & © 1964­2020 Metro-Goldwyn-MayerStudios Inc. All Rights Reserved. The color PINK is a registered trademarkof Owens Corning. © 2020 Owens Corning. All Rights Reserved. Núm. de Pub. 10011388-C. THE PINK PANTHERTM y © 1964-2020 Metro-Goldwyn-Mayer Studios Inc. Todos los derechos reservados. El color PINK es una marca comercial registrada de Owens Corning. © 2020 Owens Corning. Todos los derechos reservados. ----- page break -----